High pressure gasket for outstanding performance in many applications.
Universal material for safe and reliable sealing consisting of a unique matrix that offers an excellent combination of varied properties.
Material of construction
Aramid fibers bonded with NBR.
Surfaces
KLINGERSIL gasket materials are generally furnished with surfaces of low adhesion. On request, graphite facings and other surface finishes on one or both sides are also available. A non coloured version for food application with technically identical values is named KLINGERSIL C-4400L.
Application areas
Suitable for use with oils, water, steam, gases, salt solutions, fuels, alcohols, moderate organic and inorganic acids, hydrocarbons, lubricants and refrigerants, food industry.
Key features
- Universal high pressure gasket material
- Dimensionally stable
- Consistent material composition
Benefits
- Excellent Price/Performance ratio
- Suitable for many different media
- Very good resistance to refrigerants
Tests and approvals
- BAM approval in accordance with UVV 28
- Oxygen (VBG 62) tested up to 100 bar and 80°C
- Approved for gas supply in accordance with DIN 3535/6
- DIN-DVGW-permit NG-5123AT0251
- DIN-DVGW W 270
- DVGW VP 401
- HTB tested
- SVGW-permit
- ÖVGW Reg.No. G 1.912
- TÜV-Poland
- KTW recommended
- Food toleration Austria
- Germanischer Lloyd
- Meets the technical requirements of BS 7531:2006 Grade AY
- Elastomer-Guideline
- DNV GL
- Fire-Safe acc. to DIN EN ISO 10497
- TA-Luft (Clean air) approval
- Tested in accordance with VDI 2440 at 200°C
Standard sheet dimensions
| Sizes | 1000 x 1500 mm and 2000 x 1500 mm |
|---|---|
| Thicknesses | 0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm |
| Tolerances | Thickness acc. to DIN 28091-1 Length ±50 mm, Width ±50 mm |
Typical technical data for thickness 2.0 mm
| Compressibility ASTM F 36 J | 11 % | |
|---|---|---|
| Recovery ASTM F 36 J | 55 % | |
| Stress relaxation DIN 52913 | 50 MPa, 16 h / 175 °C | 37 MPa |
| 50 MPa, 16 h / 300 °C | 25 MPa | |
| Stress relaxation BS 7531 | 40 MPa, 16 h / 300 °C | 25 MPa |
| KLINGER cold/hot compression | thickness decrease at 23 °C | 10 % |
| 50 MPa | thickness decrease at 300 °C | 20 % |
| Tightness | DIN 28090-2 | 0.02 mg/s x m |
| Specific leakrate λ | VDI 2440 | 1.64E-08 mbar x l/s x m |
| Thickness increase after fluid immersion ASTM F 146 | oil IRM 903: 5 h / 150 °C | 3 % |
| fuel B: 5 h / 23 °C | 5 % | |
| Density | 1.6 g/cm3 | |
| Average surface resistance | ρO | 1.4x10E12 Ω |
| Average specific volume resistance | ρD | 1.2x10E12 Ω cm |
| Average dielectric strength | ED | 21.6 kV/mm |
| Average power factor | 50 Hz | 0.131 tan δ |
| Average dielectric coefficient | 50 Hz | 9.2 εr |
| Thermal conductivity | λ | 0.42 W/mK |
| Classification acc. to BS 7531:2006 | Grade AY |
ASME-Code sealing factors
| for gasket thickness 1.0 mm | tightness class 0.1 mg / s x m | MPa | y 15 m 1.2 |
|---|---|---|---|
| for gasket thickness 2.0 mm | tightness class 0.1 mg / s x m | MPa | y 15 m 1.6 |
| for gasket thickness 3.0 mm | tightness class 0.1 mg / s x m | MPa | y 15 m 4.0 |
Function and durability
The performance and service life of KLINGER gaskets depend in large measure on proper storage and fitting, factors beyond the manufactor’s control. KLINGER can, however, vouch for the excellent quality of their products.
With this in mind, please also observe their installation instructions.